In the design of the broadcast audio system, the following aspects of the device need to be carefully considered and selected:
(1) Considerations for system equipment: main equipment of the system, wiring distribution box and zone switcher, floor distribution box, volume adjuster, speaker, connecting wire.
(2) Arrangement of speakers: Arrangement of speakers: centralized arrangement, decentralized arrangement; setting distance of speakers: There are two estimation methods, one is when the 3 W speaker is used, the separation distance is (3-3.5) times Floor height or guaranteed speaker power density is 0.025-0.05W/m2. The second method is to set the distance from any part to the nearest speaker to no more than 15m, and the last speaker box at the end of the corridor is no more than 8m. .
(3) Power selection of the speaker: Speakers used in public places such as corridors, halls, restaurants, etc. of the building. If there is no special requirement, the normal rated power should be no less than 3 W; and environmental noise in entertainment places, garages, ventilation rooms, etc. For larger locations, the power of the speakers should be selected according to the requirement that the sound pressure level of the broadcast is 15 dB higher than the background noise, or the installation distance of each speaker should be appropriately reduced to achieve the desired broadcast effect. The indoor sound pressure level depends on the direct sound radiated by the speaker and the diffused sound generated by the room reflection. The sound pressure level is generally affected by 85 dB in most areas of the sound supply surface.
(4) Emergency broadcast zone switcher design: The emergency broadcast zone switcher is composed of a switch and a corresponding circuit. When the corresponding hungry switch is pressed, the switch immediately sends a control signal to the corresponding floor distribution box, so that the output of the power amplifier does not have to be directly applied to the speaker through the sound regulator, so that the full power is audible to meet the needs of the broadcast. There are several factors that must be considered when designing an emergency broadcast zone switcher: the switch of the switch must correspond to the broadcast zone number; the control information sent by the switcher to the corresponding floor junction box does not have to go through the volume adjuster; in the elevator car The speakers used are connected directly to the power amplifier and do not have to go through the junction box on the floor.
In the design of the broadcast audio system, the following aspects of the device need to be carefully considered and selected:
(1) Considerations for system equipment: main equipment of the system, wiring distribution box and zone switcher, floor distribution box, volume adjuster, speaker, connecting wire.
(2) Arrangement of speakers: Arrangement of speakers: centralized arrangement, decentralized arrangement; setting distance of speakers: There are two estimation methods, one is when the 3 W speaker is used, the separation distance is (3-3.5) times Floor height or guaranteed speaker power density is 0.025-0.05W/m2. The second method is to set the distance from any part to the nearest speaker to no more than 15m, and the last speaker box at the end of the corridor is no more than 8m. .
(3) Power selection of the speaker: Speakers used in public places such as corridors, halls, restaurants, etc. of the building. If there is no special requirement, the normal rated power should be no less than 3 W; and environmental noise in entertainment places, garages, ventilation rooms, etc. For larger locations, the power of the speakers should be selected according to the requirement that the sound pressure level of the broadcast is 15 dB higher than the background noise, or the installation distance of each speaker should be appropriately reduced to achieve the desired broadcast effect. The indoor sound pressure level depends on the direct sound radiated by the speaker and the diffused sound generated by the room reflection. The sound pressure level is generally affected by 85 dB in most areas of the sound supply surface.
(4) Emergency broadcast zone switcher design: The emergency broadcast zone switcher is composed of a switch and a corresponding circuit. When the corresponding hungry switch is pressed, the switch immediately sends a control signal to the corresponding floor distribution box, so that the output of the power amplifier does not have to be directly applied to the speaker through the sound regulator, so that the full power is audible to meet the needs of the broadcast. There are several factors that must be considered when designing an emergency broadcast zone switcher: the switch of the switch must correspond to the broadcast zone number; the control information sent by the switcher to the corresponding floor junction box does not have to go through the volume adjuster; in the elevator car The speakers used are connected directly to the power amplifier and do not have to go through the junction box on the floor.
In the design of the broadcast audio system, the following aspects of the device need to be carefully considered and selected:
(1) Considerations for system equipment: main equipment of the system, wiring distribution box and zone switcher, floor distribution box, volume adjuster, speaker, connecting wire.
(2) Arrangement of speakers: Arrangement of speakers: centralized arrangement, decentralized arrangement; setting distance of speakers: There are two estimation methods, one is when the 3 W speaker is used, the separation distance is (3-3.5) times Floor height or guaranteed speaker power density is 0.025-0.05W/m2. The second method is to set the distance from any part to the nearest speaker to no more than 15m, and the last speaker box at the end of the corridor is no more than 8m. .
(3) Power selection of the speaker: Speakers used in public places such as corridors, halls, restaurants, etc. of the building. If there is no special requirement, the normal rated power should be no less than 3 W; and environmental noise in entertainment places, garages, ventilation rooms, etc. For larger locations, the power of the speakers should be selected according to the requirement that the sound pressure level of the broadcast is 15 dB higher than the background noise, or the installation distance of each speaker should be appropriately reduced to achieve the desired broadcast effect. The indoor sound pressure level depends on the direct sound radiated by the speaker and the diffused sound generated by the room reflection. The sound pressure level is generally affected by 85 dB in most areas of the sound supply surface.
(4) Emergency broadcast zone switcher design: The emergency broadcast zone switcher is composed of a switch and a corresponding circuit. When the corresponding hungry switch is pressed, the switch immediately sends a control signal to the corresponding floor distribution box, so that the output of the power amplifier does not have to be directly applied to the speaker through the sound regulator, so that the full power is audible to meet the needs of the broadcast. There are several factors that must be considered when designing an emergency broadcast zone switcher: the switch of the switch must correspond to the broadcast zone number; the control information sent by the switcher to the corresponding floor junction box does not have to go through the volume adjuster; in the elevator car The speakers used are connected directly to the power amplifier and do not have to go through the junction box on the floor.
(1) Considerations for system equipment: main equipment of the system, wiring distribution box and zone switcher, floor distribution box, volume adjuster, speaker, connecting wire.
(2) Arrangement of speakers: Arrangement of speakers: centralized arrangement, decentralized arrangement; setting distance of speakers: There are two estimation methods, one is when the 3 W speaker is used, the separation distance is (3-3.5) times Floor height or guaranteed speaker power density is 0.025-0.05W/m2. The second method is to set the distance from any part to the nearest speaker to no more than 15m, and the last speaker box at the end of the corridor is no more than 8m. .
(3) Power selection of the speaker: Speakers used in public places such as corridors, halls, restaurants, etc. of the building. If there is no special requirement, the normal rated power should be no less than 3 W; and environmental noise in entertainment places, garages, ventilation rooms, etc. For larger locations, the power of the speakers should be selected according to the requirement that the sound pressure level of the broadcast is 15 dB higher than the background noise, or the installation distance of each speaker should be appropriately reduced to achieve the desired broadcast effect. The indoor sound pressure level depends on the direct sound radiated by the speaker and the diffused sound generated by the room reflection. The sound pressure level is generally affected by 85 dB in most areas of the sound supply surface.
(4) Emergency broadcast zone switcher design: The emergency broadcast zone switcher is composed of a switch and a corresponding circuit. When the corresponding hungry switch is pressed, the switch immediately sends a control signal to the corresponding floor distribution box, so that the output of the power amplifier does not have to be directly applied to the speaker through the sound regulator, so that the full power is audible to meet the needs of the broadcast. There are several factors that must be considered when designing an emergency broadcast zone switcher: the switch of the switch must correspond to the broadcast zone number; the control information sent by the switcher to the corresponding floor junction box does not have to go through the volume adjuster; in the elevator car The speakers used are connected directly to the power amplifier and do not have to go through the junction box on the floor.
In the design of the broadcast audio system, the following aspects of the device need to be carefully considered and selected:
(1) Considerations for system equipment: main equipment of the system, wiring distribution box and zone switcher, floor distribution box, volume adjuster, speaker, connecting wire.
(2) Arrangement of speakers: Arrangement of speakers: centralized arrangement, decentralized arrangement; setting distance of speakers: There are two estimation methods, one is when the 3 W speaker is used, the separation distance is (3-3.5) times Floor height or guaranteed speaker power density is 0.025-0.05W/m2. The second method is to set the distance from any part to the nearest speaker to no more than 15m, and the last speaker box at the end of the corridor is no more than 8m. .
(3) Power selection of the speaker: Speakers used in public places such as corridors, halls, restaurants, etc. of the building. If there is no special requirement, the normal rated power should be no less than 3 W; and environmental noise in entertainment places, garages, ventilation rooms, etc. For larger locations, the power of the speakers should be selected according to the requirement that the sound pressure level of the broadcast is 15 dB higher than the background noise, or the installation distance of each speaker should be appropriately reduced to achieve the desired broadcast effect. The indoor sound pressure level depends on the direct sound radiated by the speaker and the diffused sound generated by the room reflection. The sound pressure level is generally affected by 85 dB in most areas of the sound supply surface.
(4) Emergency broadcast zone switcher design: The emergency broadcast zone switcher is composed of a switch and a corresponding circuit. When the corresponding hungry switch is pressed, the switch immediately sends a control signal to the corresponding floor distribution box, so that the output of the power amplifier does not have to be directly applied to the speaker through the sound regulator, so that the full power is audible to meet the needs of the broadcast. There are several factors that must be considered when designing an emergency broadcast zone switcher: the switch of the switch must correspond to the broadcast zone number; the control information sent by the switcher to the corresponding floor junction box does not have to go through the volume adjuster; in the elevator car The speakers used are connected directly to the power amplifier and do not have to go through the junction box on the floor.
In the design of the broadcast audio system, the following aspects of the device need to be carefully considered and selected:
(1) Considerations for system equipment: main equipment of the system, wiring distribution box and zone switcher, floor distribution box, volume adjuster, speaker, connecting wire.
(2) Arrangement of speakers: Arrangement of speakers: centralized arrangement, decentralized arrangement; setting distance of speakers: There are two estimation methods, one is when the 3 W speaker is used, the separation distance is (3-3.5) times Floor height or guaranteed speaker power density is 0.025-0.05W/m2. The second method is to set the distance from any part to the nearest speaker to no more than 15m, and the last speaker box at the end of the corridor is no more than 8m. .
(3) Power selection of the speaker: Speakers used in public places such as corridors, halls, restaurants, etc. of the building. If there is no special requirement, the normal rated power should be no less than 3 W; and environmental noise in entertainment places, garages, ventilation rooms, etc. For larger locations, the power of the speakers should be selected according to the requirement that the sound pressure level of the broadcast is 15 dB higher than the background noise, or the installation distance of each speaker should be appropriately reduced to achieve the desired broadcast effect. The indoor sound pressure level depends on the direct sound radiated by the speaker and the diffused sound generated by the room reflection. The sound pressure level is generally affected by 85 dB in most areas of the sound supply surface.
(4) Emergency broadcast zone switcher design: The emergency broadcast zone switcher is composed of a switch and a corresponding circuit. When the corresponding hungry switch is pressed, the switch immediately sends a control signal to the corresponding floor distribution box, so that the output of the power amplifier does not have to be directly applied to the speaker through the sound regulator, so that the full power is audible to meet the needs of the broadcast. There are several factors that must be considered when designing an emergency broadcast zone switcher: the switch of the switch must correspond to the broadcast zone number; the control information sent by the switcher to the corresponding floor junction box does not have to go through the volume adjuster; in the elevator car The speakers used are connected directly to the power amplifier and do not have to go through the junction box on the floor.
Insulated Cable Terminals of compression,which are produced according to the standard of America, Japan and Germany. They are widely used in many industries, such as machinery, spinning, electric power, railway, shipbuilding, spaceflight and aviation, light industry, household electrical aaliances, computer and complete equipment of automated assmbly, etc. The surface of Insulated Compression Cooper Cable Terminals are tinned T2 copper, which assure the credible conductivity. There is thread in the inner hole of the afterbldy of terminals, the insulation covering is hard and there is no break and no rebound.
Insulated Cable Terminal,Insulated Cable Lug,Insulated Screw Terminal,Connector Cable End Terminal
Jiangsu Chuandu Electrical Technology Co.,Ltd. , http://www.cdepf.com