Siemens s7-300 digital output module, the difference between thyristor output and transistor output, mainly in which aspects, which digital output module output can directly control contactor coil, solenoid valve coil, without intermediate relay Make a transition.
Answer: 1. The output module of Siemens plc has relay output, thyristor output, and transistor output. The difference between these three outputs is simply the form:
DC = transistor; AC = thyristor; AC / DC = relay;
Transistor output speed is fast, with DC load relay output switching frequency is lower than transistor, can be AC ​​load or DC load thyristor output can only have AC load, response speed between the first two
2, can not directly output depends on whether the power output of the module can meet your requirements, pay attention to the rated current and load. It is good to be able to load.
In general, in order to protect the module, it is necessary to add.
1. Relay output: The advantage is that different common points can have different AC and DC loads, and the voltage can be different, with load current up to 2A/point; but the relay output mode is not suitable for high-frequency action load, this It is determined by the life of the relay. Its life span decreases with the increase of load current, generally between hundreds of thousands of times to Jl million times, some companies can reach more than 10 million times, and the response time is 10ms.
2. SCR output: With load capacity of 0.2A / point, only with AC load, can adapt to high frequency action, response time is 1ms. .
3. Transistor output: The biggest advantage is that it is suitable for high frequency operation, and the response time is short, generally about 0.2ms, but it can only carry DC5-30V load, the maximum output load current is 0.5A/point, but every 4 The point must not be greater than 0.8A.
a. Relay: mechanical switch device, high noise, long reflection time, short life, suitable for high power, low frequency signal (220V, 380V AC and DC signal) switching; b. Transistor: electronic switching device, low noise, reflecting Short time, long life, suitable for small power switch signal transmission, can be used for high frequency pulse signal output; c. SCR: electronic switch device, low noise, fast reflection speed, long life, can withstand the transmission of high power signals task.
12.8V200Ah Lithium Iron Phosphate Battery
Highlights
Saintish lithium iron batteries use top quality cells, which are auto grade A LiFePO4 cells with higher energy density, more stable performance . UL approved for the cells inside the battery.
The lithium-ion batteries are perfect for solar system, caravan, RVs, campers, Yacht, off-grid applications and lead aicd replacement.
Saintish Lithium Iron Phosphate Battery provides 3000+ cycles (@100%DoD) and 10 years lifespan. which is 10 times than lead-acid battery. 1/3 of the weight of lead acid, the LiFePO4 Battery weighs only 23.9kgs each pc, but delivers twice power.
Saintish lithium iron phosphate battery has built-in BMS to protect it from overcharge, over-discharge, over current, and short circuit with excellent self-discharge rate. Operating Temperature: Charge: 0°C~45°C; Discharge: -20°C~60°C.
SPECIFICATIONS
Rated Capacity | 200Ah | Charge Temperature | 0-45℃ |
Nominal Voltage | 12.8V | Connection Method | Parallel & Series |
Energy | 2560Wh | Dimensions | 522*240*218mm |
Cycle Life | >3000@100% DOD | Weight | 23.9KG |
Maximum Charging Current | 50A | Terminal Torque | 12-15N.m |
Maximum Continuous Discharging Current | 100A | Enclosure Protection | IP65 |
Discharging Voltage Range | 8.4-15.2V | Max. Batteries in Series | 4 |
Charging Voltage Range | 14.4-15.2V | Certifications | CE, UN38.3, MSDS |
Discharge Temperature | -20-60℃ | Warranty | 5 Years |
LiFePO4 Battery 200Ah, 200Ah Deep Cycle Battery, 200Ah Battery,Li Ion Battery
Hangzhou Saintish Technology Co.,Ltd. , https://www.saintishtech.com